PAN4561ETU

Make your product Powered by Panasonic

Overview

FCC Approved
The PAN4561ETU is an excellent choice for development environments and production projects where a connector or through-hole technology is required. Remember this unique part by its suffix, “ETU” which is short for “Easy-To-Use”. This module is based on Panasonic’s PAN4561 extended range RF module and features 24 pins in two single rows of 2mm header connectors on the bottom side of the module in addition to 18 pads which are accessible from the top of module allowing access to all 33 of the PAN4561 I/O lines and more.
The PAN4561 module is a long range, low power, 2.4 GHz ISM band transceiver. The module includes two antenna options, a complete 802.15.4 physical layer (PHY) modem, designed for the IEEE 802.15.4 wireless standard and an appropriate microcontroller (MCU). The RF front end consists of a power amplifier (PA) and a low noise amplifier (LNA) for extended range. This module complies with EN300328, FCC CFR Part 15 and ARIB STD-T66.
Applications
  • Remote Control
  • Wire Replacement
  • Wireless Sensor Networks
  • Factory Automation
  • Home Automation
  • Motor Control
  • Lighting Control
  • Inventory Management
  • RFID Tagging
  • AMR (Automated Meter Reading)
  • Enviornmental, Patient or Fitness Monitoring
Features:
  • 44.5mm x 39.5mm x 11.3mm
  • Interfaces with Panasonic SNAP® Development Kits
  • Antenna Options: SMA port 50Ω, ceramic antenna or plug
  • High sensitivity: -105 dBm typ. at 1% Packet Error Rate
  • 20 dBm Typical Output Power
  • Low Supply Voltage: 2.7 V to 3.3 V, 3.0 V typical
  • Operating Temperature Range: -40°C to +85°C
  • 60k Flash and 4k RAM Memory
  • Two UARTs and one I2C bus
  • 8 Channel A/D Converter With 10 Bit
  • 33 Digital I/O Lines

Software Solutions:
  • Synapse Wireless Inc. (SNAP®)
  • E-Senza Technologies GmbH (SN55) (optional)

Part Numbers:
Part Number Description
ENWC9A30A4EF 802.15.4, PAN4561ETU, Eval module with Ceramic Antenna, SNAP FW
ENWC9A30B4EF 802.15.4, PAN4561ETU, Eval Module with UFL Connector, SNAP FW
ENWC9A30D4EF 802.15.4, PAN4561ETU, Eval Module with SMD RF Out, SNAP FW
Specifications:
Parameter Value Condition / Notes
Receiver Sensitivity -105 dBm typ. For 1% Packet Error Rate
Output Power 20 dBm Typical
Power Supply 2.7 V ~ 3.3 V Single Supply, 3.0 V Typ
Power Control Range 30 dB  
Maximum Data Rate 250 kbps Over The Air
Current Consumption
  Receive Mode
  Transmit Mode
  Idle Mode
  Doze Mode
  Hibernate Mode
  Off Mode
53 mA typ.
210 mA typ.
1.6 mA typ.
36.3 uA typ.
2.2 uA typ.
0.55 uA

@Max Output Power

No CLKO
Operating Temperature Range -40°C to +85°C  
Notes:
All parameters are valid for Vcc = 3.0V and Tamb = 25°C

Freescale’s MC13213 is integrated into the module which includes mode definitions and transition times for saving battery life. Other versions of the MC1321x family of integrated circuits are available.
Pin Layout:
Notes:
Module pin names and the internal MC1321x pin names correspond to one another.
The PAN4561ETU is compatible with Panasonic SNAP and most Synapse Wireless Inc. development kits.